View MT5470D-UY_8043149.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

specification 5.24.6mm oval led lamp observe precaution for handling electro static sensitive devices attention 3 northway lane north latham,new york 12110. tollfree:1.800.984.5337 phone:1.518.956.2980 fax:1.518.785.4725 http://www.marktechopto.com part no. : mt7'-uy
description this yellow lamp is made with algainp/gap chip and yellow diffused epoxy resin. ak 1.5 typ. 2.540.1 4.6 5.2 7.8 24.0 min. 0.5 max. notes: 1. all dimensions are in mm. 2. tolerance is 0.25mm unless otherwise noted. description led chip part no. material emitting color lens color algainp/gap yellow yellow diffused 07'-8y 5.24.6mm oval led lamp 07'8< ver.: 01 date: 201 /2/ page: 1 /5
absolute maximum ratings at ta=25
parameter symbol rating unit power dissipation p d 130 mw reverse voltage v r 5 v d.c. forward current if 50 ma reverse (leakage) current ir 100 ?a peak current(1/10duty cycle,0.1ms pulse width.) if(peak) 200 ma operating temperature range topr -40 to +95
storage temperature range tstg -40 to +100
soldering temperature(1.6mm from body) tsol dip soldering : 260
for 5 sec. hand soldering : 350
for 3 sec. electrical and optical characteristics: parameter symbol condition min. typ. max. unit luminous intensity i v if=20ma 1520 2000 mcd forward voltage vf if=20ma 2.1 2.6 v peak wavelength p if=20ma 591 nm dominant wavelength d if=20ma 584 589 593 nm reverse (leakage) current ir vr=5v 100 a vertical 21/2 if=20ma 40 viewingangle horizontal 21/2 if=20ma 70 deg spectrum line halfwidth ? if=20ma 15 nm notes:1. the datas tested by is tester. 2. customer?s special requirements are also welcome. 07'-8y 5.24.6mm oval led lamp ver.: 01 date: 201 /2/ page: /5
specifications for bin grading: iv(mcd) bin min. max. u 1520 2130 v 2130 3000 specifications for vf group: vf(v) group min. max. v1 1.6 1.8 v2 1.8 2.0 v3 2.0 2.2 v4 2.2 2.4 v5 2.4 2.6 *majority vf bins are highlighted in yellow. specifications for wavelength group: ? d(nm) group min . max. x2 584 587 x3 587 590 x4 590 593 07'-8y 5.24.6mm oval led lamp ver.: 01 date: 201 /2/ page: /5
typical electrical / optica l characteristics curves : applied voltage (v) forward current vs.applied voltage forward current if(ma) 10 20 40 30 50 1.2 1.6 2.0 2.4 2.8 3.2 forward current (ma) forward current vs. luminous intensity temperature ( )
forward current vs. ambient temperature 0204060 100 80 forward current if(ma) 20 40 80 60 100 3 kqjo
8 r j-a=500
/w radiation diagram 80 90 60 70 50 30 40 0.1 0.5 0.7 0.8 0.3 1.0 0.9 0.4 0.2 0.6 0 10 20 horizontal vertical 0.0 10.0 20.0 30.0 500 1000 2500 relative luminous intensity(mcd) 1500 2000 07'-8y 5.24.6mm oval led lamp ver.: 01 date: 201 /2/ page: /5
precautions: take note of the following in use of led 1. temperature in use since the light generated inside the led needs to be emitted to outside efficiently, a resin with high light transparency is used; therefore, additives to improve the heat resistance or moisture resistance (silica gel , etc) which are used for semiconductor products such as transistors cannot be added to the resin. consequently, the heat resistant ability of the resin used for led is usually low; therefore, please be careful on the following during use. avoid applying external force, stress, and excessi ve vibration to the resins and terminals at high temperature. the glass transition temperature of epoxy resin used for the led is approximately 120-130
. at a temperature exceeding this limit, the co efficient of liner expansion of the resin doubles or more compared to that at normal temperature and the resin is softened. if external force or stress is applied at that time, it may cause a wire rupture. 2. soldering please be careful on the following at soldering. after soldering, avoided applying external force, stress, and excessive vibration until the products go to cooling process (normal temp erature), (1) soldering measurements: distance between melted solder side to bottom of resin shall be 1.6mm or longer. (2) dip soldering : pre-heat: 90
max. (backside of pcb), within 60 seconds. solder bath: 260 ? 5
(solder temperature), within 5 seconds. (3) hand soldering: 350
max. (temperature of soldering iron tip), within 3 seconds. 3. insertion pitch of the led leads and pitch of mounting holes need to be same. 4. others since the heat resistant ability of the led re sin is low, smd components are used on the same pcb, please mount the led after adhesive baking process for smd components. in case adhesive baking is done after led lamp insertion due to a production process reason, make sure not to apply external force, stress, and excessive vibration to the led and follow the conditions below. baking temperature: 120
max. baking time: within 60 seconds. if soldering is done sequentially after the adhesive baking, please perform the soldering after cooling down the led to normal temperature. 07'-8y 5.24.6mm oval led lamp ver.: 01 date: 201 /2/ page: /5

▲Up To Search▲

Price & Availability of MT5470D-UY

	To Download MT5470D-UY Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .